{"id":307,"date":"2012-04-03T15:52:26","date_gmt":"2012-04-03T07:52:26","guid":{"rendered":"http:\/\/www.luwl.net\/?p=307"},"modified":"2012-04-03T15:52:26","modified_gmt":"2012-04-03T07:52:26","slug":"%e6%81%a2%e5%a4%8d2800-%e8%b7%af%e7%94%b1%e5%99%a8%e5%af%86%e7%a0%81%e5%ae%9e%e4%be%8b","status":"publish","type":"post","link":"http:\/\/www.luwl.net\/?p=307","title":{"rendered":"\u6062\u590d2800 \u8def\u7531\u5668\u5bc6\u7801\u5b9e\u4f8b"},"content":{"rendered":"<p>\u6062\u590d\u516c\u53f8\u76842800\u8def\u7531\u5668\u5bc6\u7801<br \/>\n[cc lang=&#8221;php&#8221;]<br \/>\n\/\/\u542f\u52a8\u6309ctrl+break<br \/>\nmonitor: command &#8220;boot&#8221; aborted due to user interrupt<br \/>\nrommon 1 > confreg 0x2142<br \/>\n\/\/\u4fee\u6539confreg 0x2142<\/p>\n<p>You must reset or power cycle for new config to take effect<br \/>\nrommon 2 > reset<br \/>\n\/\/ \u91cd\u542f\u7cfb\u7edf<br \/>\nc2811 platform with 262144 Kbytes of main memory<br \/>\nMain memory is configured to 64 bit mode with ECC enabled<\/p>\n<p>Upgrade ROMMON initialized<br \/>\nprogram load complete, entry point: 0x8000f000, size: 0xcb80<br \/>\nprogram load complete, entry point: 0x8000f000, size: 0xcb80<\/p>\n<p>program load complete, entry point: 0x8000f000, size: 0x2671aa0<br \/>\nSelf decompressing the image : #################################################<br \/>\n################################################################################<br \/>\n################################################################################<br \/>\n################################################################################<br \/>\n################################################################################<br \/>\n########################################################################### [OK]<\/p>\n<p>Smart Init is enabled<br \/>\nsmart init is sizing iomem<br \/>\n  ID            MEMORY_REQ                 TYPE<br \/>\n0003E7          0X003DA000 C2811 Mainboard<br \/>\n                0X00263F50 Onboard VPN<br \/>\n                0X000021B8 Onboard USB<br \/>\n                0X002C29F0 public buffer pools<br \/>\n                0X00211000 public particle pools<br \/>\nTOTAL:          0X00B13AF8<\/p>\n<p>If any of the above Memory Requirements are<br \/>\n&#8220;UNKNOWN&#8221;, you may be using an unsupported<br \/>\nconfiguration or there is a software problem and<br \/>\nsystem operation may be compromised.<br \/>\nRounded IOMEM up to: 12Mb.<br \/>\nUsing 4 percent iomem. [12Mb\/256Mb]<\/p>\n<p>              Restricted Rights Legend<\/p>\n<p>Use, duplication, or disclosure by the Government is<br \/>\nsubject to restrictions as set forth in subparagraph<br \/>\n(c) of the Commercial Computer Software &#8211; Restricted<br \/>\nRights clause at FAR sec. 52.227-19 and subparagraph<br \/>\n(c) (1) (ii) of the Rights in Technical Data and Computer<br \/>\nSoftware clause at DFARS sec. 252.227-7013.<\/p>\n<p>           cisco Systems, Inc.<br \/>\n           170 West Tasman Drive<br \/>\n           San Jose, California 95134-1706<\/p>\n<p>Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9_IVS-M), Version 12.4(<br \/>\n9)T, RELEASE SOFTWARE (fc1)<br \/>\nTechnical Support: http:\/\/www.cisco.com\/techsupport<br \/>\nCopyright (c) 1986-2006 by Cisco Systems, Inc.<br \/>\nCompiled Fri 16-Jun-06 22:22 by prod_rel_team<br \/>\nImage text-base: 0x400B100C, data-base: 0x437A0000<\/p>\n<p>This product contains cryptographic features and is subject to United<br \/>\nStates and local country laws governing import, export, transfer and<br \/>\nuse. Delivery of Cisco cryptographic products does not imply<br \/>\nthird-party authority to import, export, distribute or use encryption.<br \/>\nImporters, exporters, distributors and users are responsible for<br \/>\ncompliance with U.S. and local country laws. By using this product you<br \/>\nagree to comply with applicable laws and regulations. If you are unable<br \/>\nto comply with U.S. and local laws, return this product immediately.<\/p>\n<p>A summary of U.S. laws governing Cisco cryptographic products may be found at:<br \/>\nhttp:\/\/www.cisco.com\/wwl\/export\/crypto\/tool\/stqrg.html<\/p>\n<p>If you require further assistance please contact us by sending email to<br \/>\nexport@cisco.com.<\/p>\n<p>Installed image archive<br \/>\nCisco 2811 (revision 49.46) with 249856K\/12288K bytes of memory.<br \/>\nProcessor board ID FHK1105F29B<br \/>\n2 FastEthernet interfaces<br \/>\n1 Virtual Private Network (VPN) Module<br \/>\nDRAM configuration is 64 bits wide with parity enabled.<br \/>\n239K bytes of non-volatile configuration memory.<br \/>\n62720K bytes of ATA CompactFlash (Read\/Write)<\/p>\n<p>         &#8212; System Configuration Dialog &#8212;<\/p>\n<p>Would you like to enter the initial configuration dialog? [yes\/no]: no<br \/>\n\/\/\u662f\u5426\u8fdb\u5165\u5411\u5bfc\u6a21\u5f0f\uff1f\u5426<\/p>\n<p>Press RETURN to get started!<\/p>\n<p>Feb 27 07:23:47.647: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0  State changed<br \/>\n to: Initialized<br \/>\nFeb 27 07:23:47.651: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0  State changed<br \/>\n to: Enabled<br \/>\nFeb 27 07:23:49.199: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0,<br \/>\n changed state to up<br \/>\nFeb 27 07:23:49.199: %LINK-3-UPDOWN: Interface FastEthernet0\/0, changed state to<br \/>\n up<br \/>\nFeb 27 07:23:49.199: %LINK-3-UPDOWN: Interface FastEthernet0\/1, changed state to<br \/>\n up<br \/>\nFeb 27 07:23:49.203: %LINEPROTO-5-UPDOWN: Line protocol on Interface IPv6-mpls,<br \/>\nchanged state to up<br \/>\nFeb 27 07:23:50.199: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEtherne<br \/>\nt0\/0, changed state to down<br \/>\nFeb 27 07:23:50.199: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEtherne<br \/>\nt0\/1, changed state to down<br \/>\nFeb 27 07:23:54.039: %SYS-5-RESTART: System restarted &#8212;<br \/>\nCisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9_IVS-M), Version 12.4(<br \/>\n9)T, RELEASE SOFTWARE (fc1)<br \/>\nTechnical Support: http:\/\/www.cisco.com\/techs<br \/>\nRouter>upport<br \/>\nCopyright (c) 1986-2006 by Cisco Systems, Inc.<br \/>\nCompiled Fri 16-Jun-06 22:22 by prod_rel_team<br \/>\nFeb 27 07:23:54.043: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing<br \/>\na cold start<br \/>\nFeb 27 07:23:54.435: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF<br \/>\nFeb 27 07:23:54.439: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF<br \/>\nFeb 27 07:23:55.515: %LINK-5-CHANGED: Interface FastEthernet0\/0, changed state t<br \/>\no administratively down<br \/>\nFeb 27 07:23:55.515: %LINK-5-CHANGED: Interface FastEthernet0\/1, changed state t<br \/>\no administratively down<br \/>\nRouter>en                                                             \/\/\u8fdb\u5165\u7279\u6743\u6a21\u5f0f<br \/>\nRouter#copy start<br \/>\nRouter#copy startup-config run                                        \/\/\u5c06\u542f\u52a8\u914d\u7f6e\u8f7d\u5165<br \/>\nDestination filename [running-config]?<\/p>\n<p>000026: Feb 27 07:24:45.403: %LINEPROTO-5-UPDOWN: Line protocol on Interface NVI<br \/>\n0, changed state to up<br \/>\n2629 bytes copied in 12.060 secs (218 bytes\/sec)<br \/>\nyxrout#conf t                                                           \/\/\u914d\u7f6e\u6a21\u5f0f<br \/>\nEnter configuration commands, one per line.  End with CNTL\/Z.<br \/>\nyxrout(config)#ena sec cisco                                            \/\/\u4fee\u6539enable\u5bc6\u7801<br \/>\nyxrout(config)#config-re<br \/>\nyxrout(config)#config-register 0x2102                                   \/\/\u4fee\u6539\u542f\u52a8\u6a21\u5f0f\u4e3a\u6b63\u5e38<br \/>\nyxrout(config)#^Z<br \/>\nyxrout#<br \/>\n000027: Feb 27 07:26:01.687: %SYS-5-CONFIG_I: Configured from console by console<br \/>\ncopy run start<br \/>\nDestination filename [startup-config]?<br \/>\nBuilding configuration&#8230;<br \/>\n[OK]<br \/>\nyxrout#sh run<br \/>\nBuilding configuration&#8230;<\/p>\n<p>Current configuration : 2633 bytes<br \/>\n!<br \/>\n! Last configuration change at 07:26:01 UTC Mon Feb 27 2012<br \/>\n! NVRAM config last updated at 07:26:15 UTC Mon Feb 27 2012<br \/>\n!<br \/>\nversion 12.4<br \/>\nservice config<br \/>\nservice timestamps debug datetime msec<br \/>\nservice timestamps log datetime msec<br \/>\nservice password-encryption<br \/>\nservice sequence-numbers<br \/>\n!<br \/>\nhostname yxrout<br \/>\n!<br \/>\nboot-start-marker<br \/>\nboot-end-marker<br \/>\n!<br \/>\nlogging buffered 4096 debugging<br \/>\nenable secret 5 $1$YZa2$3Tte1usU4LR79ihJ.Myw2.<br \/>\n!<br \/>\naaa new-model<br \/>\n!<br \/>\n!<br \/>\naaa authentication login default local<br \/>\naaa authorization exec default local<br \/>\n!<br \/>\naaa session-id common<br \/>\n!<br \/>\nresource policy<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\nip cef<br \/>\n!<br \/>\n!<br \/>\nip domain name yxjt.com<br \/>\nip ssh version 2<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\nvoice-card 0<br \/>\n no dspfarm<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\nusername hyjk privilege 15 secret 5 $1$3xLL$f7KfRQdvXYpTcdn2Zycb6\/<br \/>\nusername test@cisco.com password 7 020E1D5100545F711A400C0D44<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\ninterface FastEthernet0\/0<br \/>\n description $FW_OUTSIDE$<br \/>\n bandwidth 10000000<br \/>\n ip address 60.6.228.103 255.255.255.128<br \/>\n ip nat outside<br \/>\n ip virtual-reassembly<br \/>\n shutdown<br \/>\n duplex auto<br \/>\n speed auto<br \/>\n!<br \/>\ninterface FastEthernet0\/1<br \/>\n description $FW_INSIDE$<br \/>\n ip address 192.168.1.254 255.255.255.0<br \/>\n ip nat inside<br \/>\n ip virtual-reassembly<br \/>\n rate-limit output access-group 121 2000000 1000000 1000000 conform-action trans<br \/>\nmit exceed-action drop<br \/>\n rate-limit output access-group 122 2000000 1000000 1000000 conform-action trans<br \/>\nmit exceed-action drop<br \/>\n shutdown<br \/>\n duplex auto<br \/>\n speed auto<br \/>\n!<br \/>\nip local pool l2tp 10.1.1.100 10.1.1.150<br \/>\nip route 0.0.0.0 0.0.0.0 60.6.228.126<br \/>\nip route 192.168.0.0 255.255.255.0 192.168.1.8<br \/>\nip route 192.168.2.0 255.255.255.0 192.168.1.8<br \/>\n!<br \/>\n!<br \/>\nip http server<br \/>\nno ip http secure-server<br \/>\nip nat inside source list 1 interface FastEthernet0\/0 overload<br \/>\nip nat inside source static tcp 192.168.1.10 110 interface FastEthernet0\/0 110<br \/>\nip nat inside source static tcp 192.168.1.10 25 interface FastEthernet0\/0 25<br \/>\nip nat inside source static tcp 192.168.1.10 21 interface FastEthernet0\/0 21<br \/>\nip nat inside source static tcp 192.168.1.10 80 60.6.228.103 80 extendable<br \/>\nip nat inside source static udp 192.168.1.10 80 60.6.228.103 80 extendable<br \/>\n!<br \/>\naccess-list 1 remark SDM_ACL Category=2<br \/>\naccess-list 1 permit 192.168.1.0 0.0.0.255<br \/>\naccess-list 1 permit 192.168.0.0 0.0.0.255<br \/>\naccess-list 1 permit 192.168.2.0 0.0.0.255<br \/>\naccess-list 120 permit ip 192.168.2.0 0.0.0.255 any<br \/>\naccess-list 121 permit ip any 192.168.1.0 0.0.0.255<br \/>\naccess-list 122 permit ip any 192.168.0.0 0.0.0.255<br \/>\npriority-list 1 protocol ip high list 120<br \/>\npriority-list 1 queue-limit 40 30 20 10<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\ncontrol-plane<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\n!<br \/>\ngatekeeper<br \/>\n shutdown<br \/>\n!<br \/>\n!<br \/>\nline con 0<br \/>\nline aux 0<br \/>\nline vty 0 4<br \/>\n password 7 011B1F0E5005031B<br \/>\n!<br \/>\nscheduler allocate 20000 1000<br \/>\n!<br \/>\nend<\/p>\n<p>yxrout# conf t<br \/>\nEnter configuration commands, one per line.  End with CNTL\/Z.<\/p>\n<p>yxrout(config)#username hyjk privilege 15 secret cisco                        \/\/\u4fee\u6539\u7528\u6237\u7684\u5bc6\u7801<br \/>\nyxrout(config)#exit<br \/>\nyxrout#co<br \/>\n000028: Feb 27 07:29:20.215: %SYS-5-CONFIG_I: Configured from console by console<br \/>\npy run start<br \/>\nDestination filename [startup-config]?<br \/>\nBuilding configuration&#8230;<br \/>\n[OK]<br \/>\nyxrout#reload                                                                   \/\/\u91cd\u65b0\u542f\u52a8<br \/>\nProceed with reload? [confirm]<\/p>\n<p>000029: Feb 27 07:29:44.391: %SYS-5-RELOAD: Reload requested by console. Reload<br \/>\nReason: Reload Command.<\/p>\n<p>System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)<br \/>\nTechnical Support: http:\/\/www.cisco.com\/techsupport<br \/>\nCopyright (c) 2006 by cisco Systems, Inc.<\/p>\n<p>Initializing memory for ECC<br \/>\n.<br \/>\nc2811 platform with 262144 Kbytes of main memory<br \/>\nMain memory is configured to 64 bit mode with ECC enabled<\/p>\n<p>Upgrade ROMMON initialized<br \/>\nprogram load complete, entry point: 0x8000f000, size: 0xcb80<br \/>\nprogram load complete, entry point: 0x8000f000, size: 0xcb80<\/p>\n<p>program load complete, entry point: 0x8000f000, size: 0x2671aa0<br \/>\nSelf decompressing the image : #################################################<br \/>\n################################################################################<br \/>\n################################################################################<br \/>\n################################################################################<br \/>\n################################################################################<br \/>\n########################################################################### [OK]<\/p>\n<p>Smart Init is enabled<br \/>\nsmart init is sizing iomem<br \/>\n  ID            MEMORY_REQ                 TYPE<br \/>\n0003E7          0X003DA000 C2811 Mainboard<br \/>\n                0X00263F50 Onboard VPN<br \/>\n                0X000021B8 Onboard USB<br \/>\n                0X002C29F0 public buffer pools<br \/>\n                0X00211000 public particle pools<br \/>\nTOTAL:          0X00B13AF8<\/p>\n<p>If any of the above Memory Requirements are<br \/>\n&#8220;UNKNOWN&#8221;, you may be using an unsupported<br \/>\nconfiguration or there is a software problem and<br \/>\nsystem operation may be compromised.<br \/>\nRounded IOMEM up to: 12Mb.<br \/>\nUsing 4 percent iomem. [12Mb\/256Mb]<\/p>\n<p>              Restricted Rights Legend<\/p>\n<p>Use, duplication, or disclosure by the Government is<br \/>\nsubject to restrictions as set forth in subparagraph<br \/>\n(c) of the Commercial Computer Software &#8211; Restricted<br \/>\nRights clause at FAR sec. 52.227-19 and subparagraph<br \/>\n(c) (1) (ii) of the Rights in Technical Data and Computer<br \/>\nSoftware clause at DFARS sec. 252.227-7013.<\/p>\n<p>           cisco Systems, Inc.<br \/>\n           170 West Tasman Drive<br \/>\n           San Jose, California 95134-1706<\/p>\n<p>Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9_IVS-M), Version 12.4(<br \/>\n9)T, RELEASE SOFTWARE (fc1)<br \/>\nTechnical Support: http:\/\/www.cisco.com\/techsupport<br \/>\nCopyright (c) 1986-2006 by Cisco Systems, Inc.<br \/>\nCompiled Fri 16-Jun-06 22:22 by prod_rel_team<br \/>\nImage text-base: 0x400B100C, data-base: 0x437A0000<\/p>\n<p>This product contains cryptographic features and is subject to United<br \/>\nStates and local country laws governing import, export, transfer and<br \/>\nuse. Delivery of Cisco cryptographic products does not imply<br \/>\nthird-party authority to import, export, distribute or use encryption.<br \/>\nImporters, exporters, distributors and users are responsible for<br \/>\ncompliance with U.S. and local country laws. By using this product you<br \/>\nagree to comply with applicable laws and regulations. If you are unable<br \/>\nto comply with U.S. and local laws, return this product immediately.<\/p>\n<p>A summary of U.S. laws governing Cisco cryptographic products may be found at:<br \/>\nhttp:\/\/www.cisco.com\/wwl\/export\/crypto\/tool\/stqrg.html<\/p>\n<p>If you require further assistance please contact us by sending email to<br \/>\nexport@cisco.com.<\/p>\n<p>Installed image archive<br \/>\nCisco 2811 (revision 49.46) with 249856K\/12288K bytes of memory.<br \/>\nProcessor board ID FHK1105F29B<br \/>\n2 FastEthernet interfaces<br \/>\n1 Virtual Private Network (VPN) Module<br \/>\nDRAM configuration is 64 bits wide with parity enabled.<br \/>\n239K bytes of non-volatile configuration memory.<br \/>\n62720K bytes of ATA CompactFlash (Read\/Write)<\/p>\n<p>%Error opening tftp:\/\/255.255.255.255\/network-confg (Timed out)<br \/>\n%Error opening tftp:\/\/255.255.255.255\/cisconet.cfg (Timed out)<br \/>\n%Error opening tftp:\/\/255.255.255.255\/yxrout-confg (Timed out)<br \/>\n%Error opening tftp:\/\/255.255.255.255\/network-confg (Timed out)<br \/>\n%Error opening tftp:\/\/255.255.255.255\/yxrout.cfg (Timed out)<\/p>\n<p>Press RETURN to get started!<\/p>\n<p>Feb 27 07:31:22.635: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0  State changed<br \/>\n to: Initialized<br \/>\nFeb 27 07:31:22.639: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0  State changed<br \/>\n to: Enabled<br \/>\nFeb 27 07:31:24.187: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0,<br \/>\n changed state to up<br \/>\nFeb 27 07:31:24.187: %LINK-3-UPDOWN: Interface FastEthernet0\/0, changed state to<br \/>\n up<br \/>\nFeb 27 07:31:24.187: %LINK-3-UPDOWN: Interface FastEthernet0\/1, changed state to<br \/>\n up<br \/>\nFeb 27 07:31:24.187: %LINEPROTO-5-UPDOWN: Line protocol on Interface IPv6-mpls,<br \/>\nchanged state to up<br \/>\nFeb 27 07:31:25.187: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEtherne<br \/>\nt0\/0, changed state to down<br \/>\nFeb 27 07:31:25.187: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEtherne<br \/>\nt0\/1, changed state to down<br \/>\n000020: Feb 27 07:31:27.251: %LINEPROTO-5-UPDOWN: Line protocol on Interface NVI<br \/>\n0, changed state to up<br \/>\n000021: Feb 27 07:31:38.223: %SYS-5-CONFIG_I: Configured from memory by console<br \/>\n000022: Feb 27 07:31:39.923: %LINK-5-CHANGED: Interface FastEthernet0\/0, changed<br \/>\n state to administratively down<br \/>\n000023: Feb 27 07:31:39.991: %LINK-5-CHANGED: Interface FastEthernet0\/1, changed<br \/>\n state to administratively down<br \/>\n000024: Feb 27 07:32:19.699: %SYS-4-CONFIG_RESOLVE_FAILURE: System config parse<br \/>\nfrom (tftp:\/\/255.255.255.255\/network-confg) failed<br \/>\n000025: Feb 27 07:33:00.699: %SYS-4-CONFIG_RESOLVE_FAILURE: System config parse<br \/>\nfrom (tftp:\/\/255.255.255.255\/cisconet.cfg) failed<br \/>\n000026: Feb 27 07:33:41.699: %SYS-4-CONFIG_RESOLVE_FAILURE: System config parse<br \/>\nfrom (tftp:\/\/255.255.255.255\/yxrout-confg) failed<br \/>\n000027: Feb 27 07:34:11.699: %SYS-4-CONFIG_RESOLVE_FAILURE: System config parse<br \/>\n000027: Feb 27 07:34:11.699: %SYS-4-CONFIG_RESOLVE_FAILURE: System config parse<br \/>\n000028: Feb 27 07:34:22.699: %SYS-4-CONFIG_RESOLVE_FAILURE: System config parse<br \/>\nfrom (tftp:\/\/255.255.255.255\/yxrout.cfg) failed<br \/>\n000029: Feb 27 07:34:22.699: %SYS-5-RESTART: System restarted &#8212;<br \/>\nCisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9_IVS-M), Version 12.4(<br \/>\n9)T, RELEASE SOFTWARE (fc1)<br \/>\nTechnical Support: http:\/\/www.cisco.com\/techsupport<br \/>\nCopyright (c) 1986-2006 by Cisco Systems, Inc.<br \/>\nCompiled Fri 16-Jun-06 22:22 by prod_rel_team<br \/>\n000030: Feb 27 07:34:22.707: %SNMP-5-COLDSTART: SNMP agent on host yxrout is und<br \/>\nergoing a cold start<br \/>\n000031: Feb 27 07:34:22.919: %SYS-6-BOOTTIME: Time taken to reboot after reload<br \/>\n=  277 seconds<br \/>\n000032: Feb 27 07:34:23.103: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF<br \/>\n000033: Feb 27 07:34:23.103: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF<\/p>\n<p>User Access Verification<\/p>\n<p>Username: hyjk<br \/>\nPassword:<\/p>\n<p>yxrout>                                                                                 \/\/\u7834\u89e3\u6210\u529f<br \/>\n[\/cc]<\/p>\n","protected":false},"excerpt":{"rendered":"<p>\u6062\u590d\u516c\u53f8\u76842800\u8def\u7531\u5668\u5bc6\u7801 [cc lang=&#8221;php&#038;#8221 &hellip; <a href=\"http:\/\/www.luwl.net\/?p=307\">\u7ee7\u7eed\u9605\u8bfb <span class=\"meta-nav\">&rarr;<\/span><\/a><\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[3],"tags":[],"class_list":["post-307","post","type-post","status-publish","format-standard","hentry","category-net"],"_links":{"self":[{"href":"http:\/\/www.luwl.net\/index.php?rest_route=\/wp\/v2\/posts\/307","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.luwl.net\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.luwl.net\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.luwl.net\/index.php?rest_route=\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"http:\/\/www.luwl.net\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=307"}],"version-history":[{"count":0,"href":"http:\/\/www.luwl.net\/index.php?rest_route=\/wp\/v2\/posts\/307\/revisions"}],"wp:attachment":[{"href":"http:\/\/www.luwl.net\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=307"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.luwl.net\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=307"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.luwl.net\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=307"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}